Slot Angle Definition

Posted : admin On 7/22/2022

Plug welds are a round weld that is made inside of an existing hole most commonly in one piece of metal, welding that piece to another member. The plug weld symbol is a rectangle with a diameter symbol placed to the left of the symbol as well as the number associated with that diameter.

Slot Angle Definition

1 to 9 meaning that one side of the coil is inserted in slot #1, and the other side in slot #9. Coil Span: The number of core slots spanned by the sides of the coil. In the above example, the span would be 8 slots (9 – 1). Slots Per Pole: The number of slots in the armature core divided by the number of poles constituting the field. Slots or grooves can be short or long, closed or open, straight or non-straight, deep or shallow, wide or narrow. Explore our comparison of cutter concepts to find tools and methods best suited for your groove or slot milling operation.

Some drawings will not indicate the hole in the print so the use of dimensions come in to play when locating where a plug weld will be executed. The location will be indicated by a centerline through the part.

  • When using Hole Callout to dimension a slot in SOLIDWORKS 2009 or later, this is the type of dimension that is inserted. Method (b) The third method (c) provides the width and overall length of the slot in linear dimensions. This method is preferred if the slot has positional tolerances that use the boundary method (see ASME Y14.5M-1994 figure.
  • A right angle is an angle of 90°. Trigonometry concerns the functions of angles, such as sine, cosine and tangent. Slot piece A into piece B, taking care to keep the two pieces at right angles. Her hat was cocked at a jaunty angle.

Slot Angle Definition Geometry

Above is indicating a ½” plug weld offset 1” from the edge to the center of the weld.

SlotSlot

Slot Angle Definition Dictionary

Some plug welds may include a countersink of the hole of the plug weld. This is called the included angle of countersink. This angle is shown below the rectangle of the symbol itself or if the plug weld is to be on the other side it will be placed above the weld symbol. When figuring sizing of the hole remember that the diameter will be the narrow of the hole at the base of the weld.

Without a countersink included it will be necessary to follow shop standards and procedures to dictate what this needs to be, if any angle. Most shops have a procedure in place for tasks that will be done often. If it is needed it may be listed on a welding procedure for the plug welds that are being completed.

If a number of plug welds are needed there will be yet another element added to the symbol. This will be a number that is surrounded in parentheses, such as (6) for example.

When applying a plug weld it is important to know the depth of fill that is required. If the plug weld should fill the hole provided then the symbol will be left empty. This means there will be no dimension inside of the rectangle. If the hole should be filled only so much then this will be placed inside of the rectangle. This dimension will be in a fraction and indicates the amount in inches the hole will be filled, not the necessarily how much the hole will be filled.

Another element that can be added to this weld symbol may be the pitch (spacing) for multiple welds. This is located to the right of the symbol and is a number representing the center to center spacing for weld location.

Plug welds may have a contour symbol which will be added below the symbol or countersink angle if on the arrow side and above if it is on the other side of the reference line. There are many types of contours and finishing designations, these are covered in supplementary welding symbols.

This symbol represents:

Plug Weld

Arrow Side

½ inch in diameter

1/8” amount of fill

45 degree included angle of countersink

Flat contour

Finished by Machining

Slot Weld Symbol

The slot weld symbol is the same that is used for plug welds. The symbol will not show a diameter symbol before the size however. The size of the weld will be the slot width instead. This is shown to the left of the symbol just as it is shown in plug welds.

1/2” width slot weld

The length of the slot weld will be presented to the right of the symbol. This may also include a pitch showing the center to center spacing of the slot welds. If there is a pitch there will be a number of slot welds provided in parenthesis under the symbol on the arrow side or above the symbol on an other side weld.

The drawing must show the orientation of the slot welds as to not confuse direction along the part. The above image shows the slots with a vertical orientation to the part versus a horizontal layout as shown below.

A slot weld can include any number of elements, these are very similar to the plug weld symbol that was just explained.

These can include:

Arrow or other side

Size (width)

Length of slot

Pitch

Slot Angle Definition Meaning

Depth of fill

Number of welds required

Contour

Slot Angle Definition Math

Finish

Make no mistake on the fill of a plug or slot weld fill. There is a possibility of having a fillet weld inside of a hole versus actually filling the hole for a plug weld. This could also be mistakenly done on a slot weld.

Plug and Slot Quiz

Write down all information regarding the below Welding Symbols.